Siphonic Drainage System - Revision history

Joceil.infante at 01:23, 7 June 2019

2019-06-07T01:23:05Z

Joceil.infante at 01:20, 7 June 2019

2019-06-07T01:20:53Z

Joceil.infante: Blanked the page

2017-02-23T06:38:27Z

Blanked the page

Joceil.infante: Created page with "Drainage system in which the outlets and pipework enable the system to flow completely full under design conditions and make use of the total head available between the outlet..."

2017-01-12T04:18:27Z

Created page with "Drainage system in which the outlets and pipework enable the system to flow completely full under design conditions and make use of the total head available between the outlet..."

New page

Drainage system in which the outlets and pipework enable the system to flow completely full under design conditions and make use of the total head available between the outlets and the discharge point.

← Older revision		Revision as of 01:23, 7 June 2019
Line 19:		Line 19:
	The design of siphonic system should be determined by calculating the total head losses in the pipes and fittings at the design flow rate and ensuring that the recommendations given for minimum pressure, minimum velocity, degree of balancing between outlets, and speed of priming are met.		The design of siphonic system should be determined by calculating the total head losses in the pipes and fittings at the design flow rate and ensuring that the recommendations given for minimum pressure, minimum velocity, degree of balancing between outlets, and speed of priming are met.
	Values of pressure and velocity in the pipes should be calculated at all changes of direction or diameter in a system in order to ensure that the lowest values of these parameters are identified and are within the allowable limits.		Values of pressure and velocity in the pipes should be calculated at all changes of direction or diameter in a system in order to ensure that the lowest values of these parameters are identified and are within the allowable limits.
		+
		+	== References ==
		+	#BS EN 1253-1:2003
		+	#ASPE ANSI-45:2013
		+	#BS EN 8940:2007

← Older revision	Revision as of 01:20, 7 June 2019
Line 1:	Line 1:
	+	Pipework in siphonic drainage system are;
	+	* Smaller in pipe size,
	+	* Lesser number of rainwater downpipes,
	+	* Higher flow velocities,
	+	* Superior when comes to drainage capacity,
	+	* Generally with zero gradient on horizontal pipe run,
	+	* Ease in site coordination to installation due to its flexibility,
	+	* Minimal roof outlets with high drainage capacity,
	+	* Self-cleansing effect due to high flow velocity within the pipework.

	+	Siphonic systems are engineered on the concept of full-bore flow (fill rate of 100%) of uncompressible fluid.
	+
	+	System for drainage of rainwater in which the outlets and pipework enable the system to flow completely full under design conditions and make use of the total height available between the outlets and the point of change to partially filled flow.
	+
	+	A closed-flow roof drainage system operating under gravity-induced sub-atmospheric pressures based on the vertical differential fluid head principle (the height of a column of water expressed in pounds per square inch pressure or equivalent metric units).
	+
	+	Siphonic rainwater drainage system pipework has gone through engineering calculation.
	+
	+	The design of siphonic system should be determined by calculating the total head losses in the pipes and fittings at the design flow rate and ensuring that the recommendations given for minimum pressure, minimum velocity, degree of balancing between outlets, and speed of priming are met.
	+	Values of pressure and velocity in the pipes should be calculated at all changes of direction or diameter in a system in order to ensure that the lowest values of these parameters are identified and are within the allowable limits.

← Older revision		Revision as of 06:38, 23 February 2017
Line 1:		Line 1:
−	Drainage system in which the outlets and pipework enable the system to flow completely full under design conditions and make use of the total head available between the outlets and the discharge point.	+